Tecnologia em Metalurgia, Materiais e Mineração
https://tecnologiammm.com.br/doi/10.4322/2176-1523.1037
Tecnologia em Metalurgia, Materiais e Mineração
Artigo Original

INFLUÊNCIA DA PRÉ-DEFORMAÇÃO PLÁSTICA, DA TEMPERATURA E DO TEMPO DE AQUECIMENTO NO ENVELHECIMENTO DO AÇO BH220 ATRAVÉS DE PLANEJAMENTO DE EXPERIMENTOS

INFLUENCE OF PLASTIC PRE DEFORMATION, TEMPERATURE AND HEATING TIME IN THE AGING TREATMENT OF THE BH220 STEEL THROUGH DESIGN OF EXPERIMENTS

Ferreira, Rafael Fagundesx; Magalhães, Nathalia Sette Câmara; Carneiro, José Rubens Gonçalves; Barros, Márcio Luiz de Siqueira Campos

Downloads: 0
Views: 1015

Resumo

Aços Bake Hardening são aços laminados a frio com envelhecimento controlado. Estes aços caracterizam-se pela boa conformação e por apresentarem aumento de resistência mecânica devido à deformação e ao envelhecimento por tratamento térmico. Nesse trabalho corpos de prova de tração do material BH220 foram submetidos à pré-deformações que variam de 0% a 9% por tração uniaxial e posteriormente submetidos a tratamento térmico realizado em temperaturas que variam de 140°C a 210°C com tempos de aquecimento entre 5 minutos e 45 minutos. Foi confirmado que as temperaturas de envelhecimento, na faixa estudada, alteraram a variação do limite de escoamento devido ao fenômeno de difusão que é termicamente ativado. Verificou-se que o tempo de aquecimento, dentro do intervalo testado, não causou grandes variações nos resultados e a deformação foi a variável que maior contribuiu para o aumento de propriedade mecânica.

Palavras-chave

Aço BH220, Bake hardening, Work hardening, Planejamento de experimentos.

Abstract

Bake Hardening steels are cold rolled steels with controlled aging. These steels are characterized by a good formability and an increase in the strength due to the aging that occurs during heat treatment. In this study, tensile test specimens of the BH200 steel were submitted to pre deformations ranging from 0% to 9% by uniaxial tension, subsequently they were subjected to an aging heat treatment performed at temperatures varying from 140°C to 210°C, in heating times between 5 minutes and 45 minutes. It has been confirmed that the aging temperatures, in the range studied, modified the yield point due to the phenomenon of diffusion, which is thermally activated. In the results, it is possible to verify that the heating time, within the range tested, it is not significant and the deformation was the largest variable that contributed to the increase of mechanical properties.

Keywords

BH220 steel, Bake hardening, Work hardening, Design of experiments.

Referências

1 Ferreira FR, Ferreira JL, Silva SM, Faria ER, Bustamante GO. Estudo de viabilidade de utilização do material BH220 em substituição ao FEP04 em painel externo de um automóvel. In: Anais do 67º Congresso ABM Internacional; 2012; Rio de Janeiro. São Paulo: ABM; 2012.

2 ULSAB-AVC Program. Technical transfer dispatch 6, 05-01-2001, ULSAB-AVC body structures materials. Brussels: World Steel Association; 2001.

3 Chiang L-J, Yang K-C, Hsiao I-C. Effects of annealing conditions on bake hardenability for ULC steels. China: Iron and Steel Research & Development Department China Steel Corporation; 2011. p. 1-6.

4 Ferreira FR, et al. Influência da Temperatura e do tempo de permanência no forno do aço BH220 no resultado de Bake Hardening. In: Anais do 68º Congresso ABM Internacional; 2013; Belo Horizonte. São Paulo: ABM; 2013.

5 Borges R. Aços com envelhecimento controlado: efeito do modo e da quantidade de pré-deformação [dissertação de mestrado]. Belo Horizonte: Universidade Federal de Minas Gerais; 1994.

6 Berbenni S, Favier V, Lemoine X, Berveiller M. A micromechanical approach to model the bake hardening effect for low carbon steels. scripta Materialia. 2004;51(4):304. http://dx.doi.org/10.1016/j.scriptamat.2004.04.031.

7 Rubianes JM, Zimmer P. Proc. conf. on High Strength Sheet Steels for the Automotive Industry. Warrendale: Iron and Steel Society; 1994. p. 111-118.

8 Lora FA. Avaliação do processo de estampagem profunda de chapas de aço BH180 e BH220 utilizado na indústria automobilística [dissertação de mestrado]. Porto Alegre: Universidade Federal do Rio Grande do Sul; 2009.

9 Montgomery D, Runger G. Estatística aplicada e probabilidade para engenheiros. 5. ed. Rio de Janeiro: LTC; 2013. Planejamento de experimentos com vários fatores; p. 52. cap. 14.

10 Fiat Auto Normazione. Norma 52814: high-resistance steel sheets and strips with yeld point of 180 to 300 MPa. 3. ed. Turim: Fiat Auto Normazione; 2004.

11 Singh SB, Mohanty ON. Bake Hardening in low and medium carbon steels. Kharagpur: Indian Institute of Technology; 2012. p. 14-21.

12 Fiat Auto Normazione. Norma 50113: prova di trazione: prove di carattere generico. 6. ed. Turim: Fiat Auto Normazione; 2005.

13 Fiat Auto Normazione. Norma UNIEN 10002-1: prova di trazione: método de prova a temperatura ambiente. 1. ed. Turim: Fiat Auto Normazione; 2004.

14 ASTM International – ASTM. ASTM A-370: standard test methods and definitions for mechanical testing of steel products. West Conshohocken: ASTM International; 2014.

15 Lemos G. Efeito do recozimento em caixa do passe de encruamento nas propriedades mecânicas de um aço Bake Hardening. Florianópolis: Universidade Federal de Santa Catarina; 2011. p. 14-17.

16 Mangili I, Lasagni M, Huang K, Isayev AI. Modeling and optimization of ultrasonic devulcanization using the response surface methodology based on central composite face-centered design. Chemometrics and Intelligent Laboratory Systems. 2015;144:1-10. http://dx.doi.org/10.1016/j.chemolab.2015.03.003.

17 Kuang C, Wang J, Li J, Zhang S, Liu H, Yang H. Effect of continuous annealing on microstructure and bake hardening behavior of low carbon steel. Journal of Iron and Steel Research International. 2015;22(2):163-170. http://dx.doi.org/10.1016/S1006-706X(15)60025-5.

18 Tang Z, Ding H, Ding H, Cai M, Du L. Effect of prestrain on microstructures and properties of Si-Al-Mn TRIP steel sheet with Niobium. Journal of Iron and Steel Research International. 2010;17(4):59-65. http://dx.doi.org/10.1016/S1006-706X(10)60087-8.

5b7eee2a0e8825fe70896e52 tmm Articles
Links & Downloads

Tecnol. Metal. Mater. Min.

Share this page
Page Sections