Tecnologia em Metalurgia, Materiais e Mineração
https://tecnologiammm.com.br/doi/10.4322/2176-1523.1314
Tecnologia em Metalurgia, Materiais e Mineração
Artigo Original

CONTROLE DA PRÉ-CARGA EM PARAFUSOS: CORRELAÇÃO ENTRE O MÉTODO DO TORQUE E O ALONGAMENTO MEDIDO POR ULTRASSOM

TIGHTENING LOAD CONTROL: CORRELATION BETWEEN TORQUE METHOD AND ULTRASONIC METHOD OF BOLT ELONGATION

Goettems, Felipe Samuel; Braga, Rubem Manoel de; Reguly, Afonso

Downloads: 2
Views: 1257

Resumo

Este trabalho tem como principal objetivo comparar dois métodos de controle da pré-carga, ou seja, a tensão na qual a junta aparafusada está sujeita a experimentar. Parafusos ISO M16x2x159 bem como porcas compatíveis com esta especificação de parafusos foram utilizados no sistema. O primeiro método é o controle desta tensão através da medição do torque com torquímetro e o segundo é o controle pela medição por ultrassom do alongamento. Os parafusos foram submetidos a torque conhecido por um torquímetro de estalo e em sua extremidade o seu comprimento foi monitorado por um transdutor ultrassônico. O dispositivo foi fixado dentro de uma célula de carga para monitorar a carga efetiva aplicada quando o parafuso fora submetido ao torque. A partir dos resultados obtidos foi possível comprovar, através de equações adequadas, que o controle feito por ultrassom é muito mais confiável e apresenta resultados de carga mais próximos dos valores de carga efetiva, sempre considerando tensões dentro do regime elástico do material.

Palavras-chave

Parafuso, Torque, Ultrassom, Alongamento.

Abstract

This present work aims at comparing two methods of control of the load applied to ISO M16 x 2 x 159 fasteners. In the first method, the control is performed by measuring torque with a manual torque wrench and the second, not yet widely used, the control is performed by measuring the resulting bolt elongation with ultrasound. The bolts were subjected to torque by a click torque wrench and at its other end, its length was monitored by an ultrasonic transducer. This whole device was fixed within a load cell, so that the applied load was monitored on the bolt. The main conclusion of this work is that the control performed by ultrasound is more reliable than the control done by the torque method, obtaining results very close to the load values of effective load, considering loads under elastic region.

Keywords

Fastener, Torque, Ultrasound, Elongation.

Referências

1 Fatemi A. Metal fatigue in engineering. 2nd ed. New York: Wiley-Interscience; 2000. 472 p.

2 Suresh S. Fatigue of Materials. 2nd ed. Cambridge: Cambridge University Press; 1998. 704 p. (Cambridge Solid State Science Series).

3 Budynas R, Nisbett K. Shigley’s mechanical engineering design. 10th ed. New York: McGraw-Hill Education; 2014. 1104 p.

4 Shoberg RS. Engineering fundamentals of threaded fastener design and analysis. I. Fastening. 2000;6(2):26-29.

5 Blake A. Design of mechanical joints. New York: CRC Press; 1985. 562 p.

6 Juvinall RC, Marshek KM. Fundamentals of machine component design. 5th ed. Hoboken: Wiley; 2011. 928 p.

7 Olaru DN, Bălan MRD, Tufescu A, Cârlescu V, Prisacaru G. Influence of the cage on the friction torque in low loaded thrust ball bearings operating in lubricated conditions. Tribology International. 2017;107:294-305.

8 Guo Y, Lambert S, Wallen R, Errichello R, Keller J. Theoretical and experimental study on gear-coupling contact and loads considering misalignment, torque, and friction influences. Mechanism and Machine Theory. 2016;98:242-262.

9 Bickford J. An introduction to the design and behavior of bolted joints. 3rd ed. New York: Marcel Dekker; 1995. 951 p.

10 Vallery H, Ekkelenkamp R, Van Der Kooij H, Buss M. Passive and accurate torque control of series elastic actuators. In: 2007 IEEE/RSJ International Conference on Intelligent Robots and Systems; 2007. San Diego, CA. Canada: IEEE; 2007.

11 International Organization for Standardization – ISO. ISO 898-1:2013 - Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 1: Bolts, screws and studs with specified property classes –Coarse thread and fine pitch thread. Genebra: ISO; 2013.

12 International Organization for Standardization – ISO. ISO 16047:2005 - Fasteners -- Torque/clamp force testing. Genebra: ISO; 2005.

5b803d300e88252733896e53 tmm Articles
Links & Downloads

Tecnol. Metal. Mater. Min.

Share this page
Page Sections