Tecnologia em Metalurgia, Materiais e Mineração
https://tecnologiammm.com.br/doi/10.4322/tmm.2012.015
Tecnologia em Metalurgia, Materiais e Mineração
Artigo Original

SOLDAGEM DE TUBOS DE AÇO PATINÁVEL DE ALTO SI PELO PROCESSO HFIW

HIGH FREQUENCY INDUCTION WELDING OF HIGH SILICON STEEL TUBES

Alé, Ricardo Miranda; Faria, Adão Vieira de; Silva, Ramsés Ferreira da; Depizzol, Antônio Carlos; Reinig, Wagner de Almeida

Downloads: 0
Views: 1232

Resumo

O aço alto silício é uma alternativa de baixo custo para a fabricação de estruturas tubulares resistentes à corrosão atmosférica. Contudo a literatura, de um modo geral, indica que os aços que apresentam um alto teor de silício e/ou uma baixa relação Mn/Si são mais susceptíveis à formação de defeitos na linha de solda de juntas obtidas pelo processo HFIW (High Frequency Induction Welding – Soldagem por Indução com Alta Frequência), bastante utilizado na fabricação de tubos de pequeno diâmetro. Neste estudo é avaliada a influência das condições de soldagem pelo processo HFIW na qualidade de tubos de aço de alto silício, com baixa relação Mn/Si. A qualidade dos tubos soldados foi determinada através de teste de alargamento e os defeitos observados na linha de solda foram caracterizados via MEV. Verifica-se que, para a soldagem desse aço, devem ser utilizados valores mais elevados de velocidade, ângulo de convergência do V e potência, comparativamente a de um aço C-Mn comum de resistência mecânica similar.

Palavras-chave

Soldagem por indução com alta frequência, Aço patinável, Tubo com costura

Abstract

High-Si steel is a low cost alternative for the fabrication of tubular structures resistant to atmospheric corrosion. However, the literature has often pointed out that steels presenting a higher Si content and/or a lower Mn/Si ratio have higher susceptibility to defects at the weld bond line during HFIW (High Frequency Induction Welding) process, which has been widely used for manufacturing small diameter tubes. In this study the effect of the HFIW conditions on the quality of steel tubes with high-Si content and low Mn/Si ratio is investigated. The quality of welded tubes was determined by flare test and the defects in the bond line were identified by SEM. It has been found that higher welding speeds, V-convergence angles and power input should be applied in welding of high-Si steel, when compared to similar strength C-Mn steel.

Keywords

High frequency induction welding, Weathering steel, Seam welded pipe

Referências

1 HAGA, H.; AOKI, K.; SATO, T. Welding phenomena and welding mechanisms in high frequency electric resistance welding: 1st report. Welding Journal, v. 59, n. 7, p. 208s-16, July 1980.

2 HAGA, H. et al. Automatic heat input control in production welding of medium-diameter ERW pipe. Nippon Steel Technical Report, n. 26, p. 27-33, July 1985.

3 KIM, C.-M.; KIM, J.-K. The effect of heat input on the defect phases in high frequency electric resistance welding. Metals and Materials International, v. 15, n. 1, p. 141-8, 2009. http://dx.doi.org/10.1007/s12540-009-0141-5

4 YOKOYAMA, E. et al. Effects on penetrator defect occurrence of welding conditions and Mn/Si ratio of ERW high manganese line pipe. Kawasaki Steel Giho, v. 10, n. 1, p. 23-33, 1978.

5 ICHIHARA, H. et al. Manufacture of alloy steel tube by high frequency electric resistance welding. Transactions ISIJ, v. 26, p. 468-75, 1986. http://dx.doi.org/10.2355/isijinternational1966.26.468

6 ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS. NBR NM 168. Tubos de aço: Ensaio de alargamento. Rio de Janeiro, 2000.

7 LANDGRAF, F. J. G. Lâminas de aço para motores elétricos. Metalurgia e Materiais, v. 55, n. 483, p. 626-7, 1999.

588696997f8c9dd9008b45ee tmm Articles
Links & Downloads

Tecnol. Metal. Mater. Min.

Share this page
Page Sections