Tecnologia em Metalurgia, Materiais e Mineração
https://tecnologiammm.com.br/article/doi/10.4322/2176-1523.20191724
Tecnologia em Metalurgia, Materiais e Mineração
Artigo Original

ANÁLISE DA MARTENSITA INDUZIDA POR DEFORMAÇÃO DE UM AÇO INOXIDÁVEL AUSTENÍTICO 304L COM CONCENTRADORES DE TENSÃO SUBMETIDO A FADIGA DE BAIXO CICLO

ANALYSIS OF THE STRAIN-INDUCED MARTENSITE OF A 304L AUSTENITIC STAINLESS STEEL WITH STRESS CONCENTRATORS SUBJECTED TO LOW CYCLE FATIGUE

Jéssica Gadêlha Chaves, Gláucio Soares da Fonseca, Luiz Carlos Rolim Lopes

Downloads: 5
Views: 1178

Resumo

Os aços inoxidáveis austeníticos metaestáveis sofrem transformações de fase de microestrutura austenítica para martensítica quando sujeitos à deformação a frio, melhorando significativamente sua resistência mecânica (efeito TRIP). A transformação é influenciada pela temperatura, composição química, taxa de deformação e estado de tensões durante a deformação. Para compreender a transformação martensítica no AISI 304L, foram analisadas amostras com e sem descontinuidade circular submetidas a esforços cíclicos. Existem poucos trabalhos relacionando a transformação martensítica com estes tipos de esforços, e em muitos casos, estes aços estão submetidos a este carregamento. A análise da martensita αʹ foi feita através de ferritoscopia e sua morfologia obtida via microscopia ótica. Os resultados mostraram para a amostra sem descontinuidade circular, que ocorre uma saturação da deformação e os laços de histerese ficaram sobrepostos, não havendo a necessidade de um elevado número de ciclos para se obter uma deformação em torno de 0,10 e uma fração volumétrica de martensita entre 6 e 7%. Após ensaio de fadiga em diferentes frequências para amostras com descontinuidade circular notou-se que em frequências menores, as amostras apresentam próxima a descontinuidade circular maiores frações volumétricas de martensita, pois o trabalho da deformação é menor, sendo assim sofrem menos com o efeito da temperatura que tende a inibir a transformação de fase.

Palavras-chave

Aço inoxidável austenítico 304L; Efeito TRIP; Fadiga de baixo ciclo; Transformação martensítica.

Abstract

The metastable austenitic stainless steels undergo phase transformations of austenitic microstructure for martensitic when subjected to cold deformation, significantly improving its mechanical resistance (TRIP effect). The transformation is influenced by the temperature, chemical composition, deformation rate and tensions states during deformation. In order to understand the martensitic transformation in AISI 304L, samples with and without circular discontinuity and cyclic load were analyzed. There are few works relating the martensitic transformation to these types of stress state, and in many cases, these steels are subjected to this loading. The analysis of α’ martensite was done by means of the ferritescope and its morphology obtained by optical microscopy. The results showed for the sample without circular discontinuity, that a deformation saturation occurs, and the hysteresis loops were superimposed, not requiring a high number of cycles to obtain a deformation around 0.10 and a volume fraction of martensite between 6 and 7%. After fatigue test at different frequencies for samples with circular discontinuity, it was noticed that in the lower frequencies, the samples presented near the circular discontinuity greater volumetric fractions of martensite, since the deformation work is smaller, undergoing thus less with the effect of the temperature which tends to inhibit phase transformation

Keywords

304L austenitic stainless steel; TRIP effect; Low cycle fatigue; Martensitic transformation.

Referências

1 Costa e Silva ALV, Mei PR. Aços e ligas especiais. 2. ed. São Paulo: Edgard Blucher; 2006.

2 Talonen J. Effect of strain-induced α’-martensite transformation on mechanical properties of metastable austenitic stainless steels [dissertation]. Espoo: Helsinki University of Technology; 2007.

3 Hecker SS, Stout MG, Staudhammer KP, Smith JL. Effects of strain state and strain rate on deformation-induced transformation in 304 stainless steel. Part I. Magnetic measurements and mechanical behavior. Metallurgical Transactions. 1982;A13:619-626.

4 Tavares SSM, Pardal JM, da Silva MJG, Abreu HFG, Silva MR. Deformation induced martensitic transformation in a 201 modified austenitic stainless steel. Materials Characterization. 2009;60:907-911.

5 Spencer K, Embury JD, Conlon KT, Véron M, Bréchet Y. Strengthening via the formation of strain-induced martensite in stainless steels. Materials Science and Engineering. 2004;387-389:873-881.

6 Sales LS. Envelhecimento na martensita induzida por deformação em aços tipo AISI 30 [dissertação]. Belo Horizonte: Universidade Federal de Minas Gerais; 2006.

7 Alves JM. Análise da transformação martensítica e tensão residual em um aço inoxidável 304L [dissertação]. Rio de Janeiro: Instituto Militar de Engenharia; 2014.

8 Maier HJ, Schneeweiss O, Donth B. Kinetics of fatigue-induced phase transformation in a metastable austenitic 304L type steel at low temperatures. Scripta Metallurgica et Materialia. 1993;29:521-526.

9 Zhang SH, Xu Y, Cheng M, Song HW. In situ X-ray diffraction study of martensitic transformation in austenitic stainless steel during cyclic tensile loading and unloading. Scripta Materialia. 2012;67:771-774.

10 Peterson RE. Stress concentration factors. New York: John Wiley & Sons; 1974.

11 Colin J, Fatemi A, Taheri S. Cyclic hardening and fatigue behavior of stainless steel 304L. Journal of Materials Science. 2011;46(1):145-154.

12 Hertzberg RW. Deformation and fracture mechanics of engineering materials. New York: John Wiley & Sons; 1976.

13 Russ JC, Dehoff RT. Practical stereology. 2. ed. New York. Kluwer Academic/Plenum Publishers; 2000.

14 Talonen J, Aspegren P, Hanninen H. Comparison of different methods for measuring strain induced α′-martensite content in austenitic steels. Materials Science and Technology. 2004;20:1506-1512.

5dee51c10e88259e71b5f733 tmm Articles
Links & Downloads

Tecnol. Metal. Mater. Min.

Share this page
Page Sections