Tecnologia em Metalurgia, Materiais e Mineração
https://tecnologiammm.com.br/article/doi/10.4322/tmm.2012.038
Tecnologia em Metalurgia, Materiais e Mineração
Artigo Original

DESENVOLVIMENTO DE FLUXANTE ISENTO DE FLÚOR APLICADO EM AÇOS BAIXO CARBONO

DEVELOPMENT OF FLUORINE-FREE MOULD FLUX APPLIED IN LOW CARBON STEEL

Souza Junior, Jayme Alves de; Pontes Junior, José Carlos; Santos, Sandro de Souza; Bezerra, Maria Carolina C.; Valadares, Claudio Antônio G.; Diego, Alexandra de Almeida

Downloads: 0
Views: 1046

Resumo

O fluxante é composto por uma mistura de materiais não metálicos que, em contato com o aço líquido, funde formando escória que age principalmente como lubrificante e controla a transferência de calor na interface placa/molde durante o lingotamento contínuo de aços. O fluxante sem flúor, quando comparado ao fluxante convencional, apresenta como vantagens a redução tanto do desgaste da máquina, quanto da válvula submersa. A sua aplicação no lingotamento contínuo de placas tem sido um grande desafio no que se refere à sua viabilidade operacional aliado à qualidade interna e superficial das placas. Outro diferencial do fluxante sem flúor é a redução de problemas ambientais, devido à contaminação da água do resfriamento secundário por fluoretos. Considera-se que as propriedades dos fluxantes, como composição química, viscosidade, temperaturas de amolecimento, fusão e fluidez, velocidade de fusão etc., devem estar adequadas à composição química e às propriedades mecânicas a quente do aço, bem como aos parâmetros operacionais de temperatura, velocidade de lingotamento, frequência de oscilação do molde, entre outros. Este trabalho mostra uma análise preliminar do uso do fluxante sem flúor no que se refere à viabilidade operacional, qualidade das placas produzidas e contaminação da água de refrigeração secundária da máquina. Também são analisados fatores operacionais como desgaste de SEN, consumo do fluxante, nível de escória no molde e o comportamento dos termopares do sistema de detecção de rompimento (MSD).

Palavras-chave

Fluxantes sem flúor, Propriedades físico-químicas, Lingotamento contínuo de placas

Abstract

The mould flux is a mixture of non-metallic oxides that, in contact with liquid steel melts, becomes a liquid slag which the mainly function is to lubricate and control heat transfer between mould and strand during the continuous casting process. The mould flux without fluoride has the advantage of decreasing the wear of machine and the SEN in comparison to common mould flux. The application in Continuous Casting of Slabs has been a great challenge in relation to the operational viability together with internal and surface quality of slabs. Another differential is the decrease of environmental issues on account of the contamination of secondary cooling water by the fluorides. It is considered that properties of mould flux as chemical composition, viscosity, softening, melting flowing temperatures, fusion rate, etc, should be suitable to the chemical composition and the mechanical properties at elevated temperatures of steel and also the operational parameters such as casting temperature, casting speed, mould frequency, among others. This work presents a preliminary analysis in relation to operational viability, analysis of surface quality of slabs, measurements of fluorides content in the water of secondary cooling of machine. In addition to that, the analyses of operational features as measurements of wear of SEN, mould flux consumption, slag pool and behavior of thermocouples of detection system break outs (MSD) are considered.

Keywords

Mould flux without fluoride, Physical chemical properties, Cristislab continuous casting

Referências

1 ZACHARIASEN, W. H. The atomic arrangement in glass. Journal of the American Chemical Society, v. 54, n. 10, p. 3841-51, Oct. 1932. http://dx.doi.org/10.1021/ja01349a006

2 FOX, A. et al. Development of fluoride-free fluxes for billet casting. ISIJ International, v. 45, n. 7, p. 1051-8, May 2005. http://dx.doi.org/10.2355/isijinternational.45.1051

3 PINHEIRO, C. A.; SAMARASEKERA, I. V.; BRIMACOMBE, J. K. Mould flux for continuous casting of steel. Part I e II. Iron and Steelmaker, v. 62, p. 55-6, Oct. 1994.

4 FOX, A. B. et al. Dissolution of ZrO2, Al2O3, MgO and MgAl2O4 particles in a B2O3 containing commercial fluoridefree mould slag. ISIJ International, v. 44, n. 5, p. 836-45, Jan. 2004. http://dx.doi.org/10.2355/isijinternational.44.836

5 ZAITSEV, A. I. et al. Investigation of the mould powder volatiles during continuous casting. Steel Research, v. 65, n. 9, p. 368-74, Sep. 1994.

6 ZHANG, Z.; WEN, G.; ZHANG, Y. Crystallization behavior of F-free mold fluxes. ISIJ International, v. 18, n. 2, p. 150-8, Apr. 2011.

7 WEN, G. et al. Development of fluoride-free mold powders for peritectic steel slab casting. ISIJ International, v. 47, n. 8, p. 1117-25, Aug. 2007. http://dx.doi.org/10.2355/isijinternational.47.1117

8 XIN QI; WEN, G.; PING TANG. Investigation on heat transfer performance of fluoride-free and titanium-bearing mold fluxes. Journal of Non-Crystalline Solids, v. 354, n. 52-54, pp. 5444-52, 2008. http://dx.doi.org/10.1016/j. jnoncrysol.2008.09.012

9 CAMPELLO, M. C. B. Avaliação do efeito do carbono em fluxantes para lingotamento contínuo de aços. 2006. 129 p. Tese (Mestrado – Engenharia Metalúrgica e de Materiais) – Escola Politécnica da Universidade de São Paulo, São Paulo, 2006.

10 DIEGO, A. A. et al. Influência do fluxante na redução do desgaste de válvula submersa no molde de lingotamento contínuo. In: 41o SEMINÁRIO DE ACIARIA – INTERNACIONAL, 41.,2010, Resende. Anais... São Paulo: ABM, 2010. p. 728-35.

588696957f8c9dd9008b45dd tmm Articles
Links & Downloads

Tecnol. Metal. Mater. Min.

Share this page
Page Sections